Standard and custom titanium fasteners — bolts, nuts, screws, studs and washers — offering high corrosion resistance with roughly half the weight of steel equivalents for demanding assemblies.
Twelve precision titanium fastener and standard-part types referenced to common DIN / ISO standards — each with its own dedicated page.
Hex socket drive cap screws — the most common titanium fastener for precision assembly.
Hexagon head bolts — full thread (DIN 933) and partial thread (DIN 931) variants.
Countersunk hex socket drive screws for flush-surface assembly requirements.
Standard hex nuts in matching titanium grades for bolted assemblies.
Plain flat washers for bolted and screwed assemblies — grade matched to fasteners.
Phillips drive pan head (DIN 7985) and countersunk (DIN 965) machine screws.
Torx (star drive) screws in pan head and countersunk configurations for high-torque precision assembly.
Button head hex socket drive screws for low-profile, visually clean assembly.
Socket set screws — flat point (DIN 913), cone point (DIN 914), dog point (DIN 915) and cup point (DIN 916).
Double-ended stud bolts — equal thread (DIN 938), unequal (DIN 939) and fully threaded stud stock (DIN 975).
Flange head bolts and flange serrated nuts for high-pressure flange assemblies.
Self-tapping Phillips pan head screws for sheet metal and thin-section assembly.
Titanium fasteners are the preferred assembly choice when corrosion resistance, weight reduction or biocompatibility matters more than raw tensile strength alone. Commercially pure titanium fasteners (Grade 1 and Grade 2 CP) are used in non-load-bearing or moderately loaded assemblies where chemical resistance is the primary requirement, while alloy-grade fasteners — most commonly Grade 5 (Ti-6Al-4V), also Grade 7, 9, 12 and 23 — are specified when higher shear and tensile strength must be combined with titanium's corrosion properties. Grade 2 CP titanium and Grade 5 (Ti-6Al-4V) alloy fasteners are available from stock. Grade 1, 7, 9, 12 and 23 are available on a per-inquiry basis.
Feinuotai supplies fasteners to the thread and dimension standards specified in your inquiry, as well as non-standard configurations to customer drawings; applicability is verified before order confirmation. Available types include hex head bolts, socket head cap screws, carriage bolts, machine screws, hex and lock nuts, stud bolts, flat and spring washers, and custom pins, rivets and plugs. For each inquiry we confirm specification, grade, surface finish and quantity before quoting.
No single ASTM standard covers all titanium fastener configurations end-to-end. Applicable standards are selected according to the specific fastener type, material form, dimensions and performance requirements. DIN 912 / ISO 4762 for socket head cap screws, DIN 931 / DIN 933 for hex bolts, DIN 934 / ISO 4032 for hex nuts, and related DIN / ISO product standards are applied where the selected titanium grade and manufacturing route permit. Thread tolerances follow 6g (external) / 6H (internal) class unless specified otherwise. ASTM F468 (Nonferrous Bolts, Hex Cap Screws, and Studs for General Use) and ASTM F467 (Nonferrous Nuts for General Use) are reviewed as applicable per the specific product and material.
Four titanium grades are routinely used for fasteners — Grade 2 (commercially pure), Grade 5 (Ti-6Al-4V), Grade 7 (Ti-0.2Pd) and Grade 23 (Ti-6Al-4V ELI). Grade 2 and Grade 5 fasteners are available from stock; Grade 7 and Grade 23 are supplied on a per-inquiry basis.
Mechanical properties of titanium fasteners depend on the selected material grade, fastener type, dimensions, manufacturing route, and applicable product requirements. Final mechanical properties should be confirmed against the agreed technical specification and relevant test documentation.
Not every strength statement applies to every fastener type.
Titanium fasteners are supplied in a comprehensive range of metric and inch thread forms, head configurations and surface finishes.
| Parameter | Standard Options |
|---|---|
| Thread Form | Metric (M2 – M24), UNC, UNF, BSP (per standard) |
| Thread Class | 6g (external), 6H (internal) — standard |
| Head Style | Socket cap, countersunk, hex, button, pan, flange |
| Drive | Hex socket, Phillips, Torx |
| Surface Finish | Use Case |
|---|---|
| Plain (As Machined) | General-purpose, most cost-effective |
| Passivated | Improved corrosion resistance, cosmetic consistency |
| Oxide / Black Oxide | Aesthetic finish for precision assembly |
| Dry-Film Lubricated | Low-friction assembly, controlled torque |
| Nylon Patch / Serrated | Self-locking (limited standard; custom quote) |
Beyond the 12 standard fastener types cataloged, Feinuotai coordinates the production of custom, drawing-based titanium fasteners — unusual head configurations, special thread forms, custom lengths and non-metric sizes. These are coordinated through our manufacturing partners and tooling program.
You may share your drawings with our sales team by email or WhatsApp after initial contact.
Corrosion-resistant fasteners for flanges, tanks and machinery exposed to acids.
Low-weight, high-strength fasteners in structural and engine-adjacent assemblies.
Biocompatible titanium fasteners for surgical instruments and orthopedic assemblies.
Fasteners resisting saltwater corrosion in marine and coastal installations.
Grade 2 CP titanium and Grade 5 (Ti-6Al-4V) alloy fasteners are available from stock. Grade 1, 7, 9, 12 and 23 are available on a per-inquiry basis.
Fasteners are supplied to the thread and dimension standards specified in your inquiry, as well as non-standard configurations to customer drawings; applicability is verified before order confirmation.
Tell us the fastener type, size, thread form, grade and quantity — or send a drawing for custom head shapes, special threads or unusual sizes. For each inquiry we confirm specification, grade, surface finish and quantity before quoting.
No single "strength class" designation covers all titanium fastener configurations. Mechanical properties of titanium fasteners depend on the selected material grade, fastener type, dimensions, manufacturing route, and applicable product requirements. Final mechanical properties should be confirmed against the agreed technical specification and relevant test documentation for each specific part, diameter and application at the inquiry stage.
We maintain standard stock for DIN 912 (socket cap), DIN 933/931 (hex bolts), DIN 7991 (countersunk socket), DIN 934 (hex nuts) and related fastener families. Additional DIN/ISO standards are coordinated per inquiry.
Plain passivated titanium is our standard finish. Nylon patch self-locking, serrated flange nuts and dry-film-lubricated variants are available — confirm the type and quantity in your inquiry as some require minimum tooling runs.
For drawing-based or custom titanium fastener requirements, you may share your drawings with our sales team by email or WhatsApp after initial contact. Include fastener type, thread form, diameter/length, grade, quantity and drawing reference.
Send Inquiry
